The AquaFlex Advantage

Competitor Comparison
Comparison AquaFlex Competitor #1 Competitor #2
5/8" Factory Pull Tested To: 7,500 lbs. Doesn’t
Pull Test
Doesn’t
Pull Test
3/4" Factory Pull Tested To: 10,000 lbs. Doesn’t
Pull Test
Doesn’t
Pull Test
5/8" Rod Destruction Point: 20,000 lbs. 10,350 lbs. 17,900 lbs.
3/4" Rod Destruction Point: 40,000 lbs. Rod Size
Not Offered
17,900 lbs.
Non-"Flow Restricting"
Rod Guides?
Yes No No
416 Stainless Steel Couplings? Yes No No
5 Year Guarantee? Yes No No

Table of Pumping Capacities and Maximum Operating Elevations for  5/8"  AquaFlex Sucker Rod
Diameter
of
Cylinder
(inches)
PumpingCapacity
(Gallons per Hour)
Pumping Elevation (Feet)
Wheel Diameter
6’ Ft. 8-16’ Ft. 6’ 8’ 10’ 12’ 14’ 16’
Long Stroke
1 3/4" 105 150 152’ 216’ 328’ 491’ 702’ 1170’
1 7/8" 125 180 140’ 205’ 304’ 456’ 655’ 1076’
2" 130 190 111’ 164’ 252’ 374’ 538’ 878’
2 1/4" 180 260 90’ 129’ 199’ 293’ 421’ 690’
2 1/2" 225 325 76’ 111’ 164’ 246’ 351’ 573’
2 3/4" 265 385 66’ 94’ 140’ 211’ 304’ 467’
3" 320 470 55’ 80’ 117’ 181’ 257’ 421’
3 1/4" 370 550 48’ 68’ 105’ 152’ 216’ 357’
3 1/2" 440 650 41’ 59’ 89’ 135’ 187’ 310’
3 3/4" 500 730 35’ 51’ 76’ 117’ 170’ 269’
4" 570 830 32’ 46’ 68’ 99’ 146’ 234’
4 1/4" *** 940 *** 40’ 60’ 89’ 129’ 211’
4 1/2" 725 1050 25’ 35’ 54’ 80’ 117’ 187’
4 3/4" *** 1170 *** *** 48’ 71’ 105’ 164’
5" *** 1300 20’ 29’ 43’ 64’ 94’ 152’
5 3/4" *** 1700 *** *** *** 47’ 70’ 117’
6" *** 1875 *** 20’ 29’ 44’ 64’ 99’
7" *** 2550 *** *** 22’ 33’ 48’ 76’
8" *** 3300 *** *** 16’ 26’ 36’ 59’
Short Stroke
1 3/4" 79 113 205’ 287’ 439’ 655’ 936’ 1562’
1 7/8" 94 135 187’ 275’ 404’ 608’ 782’ 1433’
2" 98 143 146’ 216’ 333’ 497’ 714’ 1170’
2 1/4" 135 195 117’ 170’ 263’ 392’ 562’ 918’
2 1/2" 169 244 99’ 146’ 216’ 328’ 468’ 766’
2 3/4" 199 289 88’ 123’ 187’ 281’ 404’ 661’
3" 240 353 74’ 105’ 158’ 240’ 345’ 562’
3 1/4" 278 413 64’ 90’ 140’ 205’ 287’ 474’
3 1/2" 330 480 55’ 78’ 117’ 181’ 252’ 415’
3 3/4" 375 548 47’ 68’ 99’ 158’ 228’ 357’
4" 428 623 42’ 61’ 90’ 135’ 193’ 310’
4 1/4" *** 705 *** 53’ 80’ 117’ 170’ 281’
4 1/2" 544 788 33’ 47’ 71’ 105’ 158’ 252’
4 3/4" *** 878 *** *** 64’ 94’ 140’ 216’
5" 675 975 27’ 39’ 57’ 85’ 123’ 205’
5 3/4" *** 1275 *** *** *** 62’ 94’ 158’
6" *** 1406 *** 27’ 39’ 60’ 85’ 135’
7" *** 1912 *** *** 22’ 34’ 48’ 78’
8" *** 2475 *** *** 22’ 34’ 48’ 78’

Capacities are approximate and based on the mill operating in normal wind speeds. In 12 MPH winds, capacity is reduced about 20%; in 10 MPH winds, about 38%. If prevailing winds are low, use of a cylinder smaller than the one shown will permit your mill to operate in lower winds. Never use pipe smaller than the size specified for the cylinder.


 

Contact Us At   888.535.4788   |   Terms & Conditions
© 2014. All Rights Reserved.